电动滚筒烧掉，有两个原因：1、缺电相，2、电动滚筒疲劳，即使用时间过长（连续使用1 5 个小时以上）；此两项制造方概不负责，正常使用保修一年。
6、为减轻物料对胶带的冲击与磨损，给料方向应顺胶带的运行方向；物料下落到胶带上的落 差应尽量的减??；给料口应避开滚筒或托辊的正上方；胶带受料段应缩短托辊间距和采取 缓冲措施。为防止刮破胶带，挡料装置、刮板清扫装置和卸料装置与胶带的接触部分应采 用硬度适宜的橡胶板，不要采用夹有布层的胶带头。
Use one, the note
Boot: the mobile car first positioning (note after startup it is forbidden to move the car), and then start from the last section of the belt conveyor machine) (that is, the stone fall in the wagon, in turn, starting in sequence. The car in the opposite direction of horizontal belt operation must first stop (cannot be switch in material handling), such as violation of operating responsibility conceited.
Second, the use of common problems and solutions:
(1), belt running deviation:
Belt running deviation has a variety of factors, the weather (rain) or damp, belt machine vibration, blanking offset, such as weather or material on the wet easy to make the big drum and small roller on the drum is bold belt running deviation, fines should always check to see if there is this phenomenon timely removal of fine material.
Vibration cause of belt conveyor idler bracket screw loosening, stent displacement, make the belt running deviation, if found, will support and big Angle between 90 degrees, the screw can be.
Blanking offset should always check the position of the hopper and belt.
Caused by complicated reasons, but please send professional personnel adjustment.
(2), belt tear:
If there is foreign body on the card in the roller roller, belt rotating foreign body motionless, the belt longitudinal tear, to check for foreign material on belt when the working face and check whether the small roller damage, if any should be replaced in a timely manner. If you have this kind of situation, responsibility conceited.
(3), electric drum:
Electric drum burn, for two reasons: 1, the power shortage, 2, electric drum fatigue, which USES time is too long (more than 5 hours of continuous use 1); The two, the manufacturer is not responsible for normal use of the warranty for one year.
Third, repair and maintenance
(1) belt: such as hair view belt with local damage should be repaired in a timely manner, to avoid affect the service life of the belt:
(2) roller, roller and the tube always point between the oil roller to maintain the flexibility:
(3) electric drum: once every three months to add oil, how much depending on the degree of oil consumption. Half an year is need to change the oil:
(4) the big drum: six months in a bearing or depending on the usage:
(5) frame: frame all screws should be check regularly, will loose screw.
Conveyor belt storage use matters needing attention
1, the conveyor belt in transportation and storage, should be kept clean, avoid direct sunlight, rain and snow shower, prevent with acid, alkali, oil, organic solvent, affecting the quality of rubber material such as contact and distance heating device 1 metres away.
2, storage room temperature should be keep between 50 c - 1 + 400 c, relative humidity should be kept between 50-80%.
3, storage in the conveyor belt must be placed in rolls, not fold, should be placed during quarterly turn once.
4, conveyor belt running speed should not be more than 5.0 m/s, large transport blocks of abrasion resistant materials and using a fixed type plow discharge Should as far as possible when using low speed. Within the prescribed speed, will influence the service life of the tape.
5, the transmission roller conveyor, and the relationship between conveyor belt layers and the diameter of the transmission drum redirection roller supporting and requirement for roller groove Angle, should according to the regulations of the design of the conveyor, reasonable selection.
6, to reduce the material impact on tape and wear and tear, the feeding direction should be along the belt running direction; Difference in whereabouts to fall on the tape should be reduced; The feeding mouth to avoid roller or roller is directly above; Tape material section should shorten the roller spacing and buffer action. To prevent scraping the broken belt, keep-off device, scraper cleaning device, and discharging device with the contact part of the tape should be taken With suitable rubber hardness, do not use with layers of glue to take the lead.
7, conveyor belt in use should be paid attention to the following:
A, avoid rollers is covered by the material, causing the rotation is ineffective, prevent leakage of material between the roller and the tape, pay attention to the lubrication activities section, but not oil conveying Fei.
B, makes every effort to avoid loading start.
C, belt running deviation, timely measures should be taken to correct.
D, find tape local damage should be repaired in a timely manner, so as not to expand.
E, avoid tape rack, pillar or block material retardation, prevent touch broken rip.